Skill saw owner manual

Accessories that may be suitable for one tool, may become hazardous when used on another tool. Use clamps or a vise to hold work. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.

These tools are precision built. Any alteration or modification not specified is misuse and may result in dangerous conditions. Do not operate electric tools in gaseous or explosive at mospheres. Motors in these tools normally spark, and may result in a dangerous condition. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility.

Inspect extension cords periodically and replace if damaged. Keep handles dry, clean and free from oil and grease. Before connecting the tool to a power source receptacle, outlet, etc. A power source with voltage greater than that specified for the tool can result in serious injury to the user — as well as damage to the tool.

Using a power source with voltage less than the nameplate rating is harmful to the motor. For your own safety, do not operate your! General Safety Rules.

Double Insulated Tools. Basic Table Saw Operation. Maintaining Your Table Saw. In addition, if there is any tendency for the table saw to tip over or move during certain operations such as cutting long, heavy boards, use an auxiliary support.

Use the table saw in a well lit area and on a level surface, clean and smooth enough to reduce the risk of trips and falls. Use it where neither the operator nor the casual observer is forced to stand in line with the blade.

Workpiece binding the blade due to misalignment, can also cause kickback. During kickback, workpiece rises from table and is thrown toward the operator. Maintaining the rip fence parallel to the sawblade. Keeping the sawblade sharp. Replacing or sharpening anti-kickback pawls when points become dull. Keeping sawblade guard, spreader and anti-kickback pawls in place and operating properly.

The spreader must be in alignment with the sawblade and the pawls must stop a kickback once it has started. Check their action before ripping.

NOT ripping workpiece that is twisted or warped or does not have a straight edge to guide along the rip fence. NOT releasing work until you have pushed it all the way past the sawblade.

NOT confining the cut-off piece when ripping or crosscutting. When ripping, apply the feed force to the section of the workpiece between the sawblade and the rip fence. If any part of your saw is missing, malfunctioning, has been damaged or broken … such as the motor switch, or other operating control, a safety device or the power cord … cease operating immediately until the particular part is properly repaired or replaced. Wear safety goggles and a face shield if operation is dusty.

Wear ear plugs or muffs during extended periods of operation. Small loose pieces of wood or other objects that contact the rear of the revolving blade can be thrown back at the operator at excessive speed. Use extra caution when the guard assembly is removed for resawing, dadoing, rabbeting or molding — replace the guard as soon as that operation is completed.

NEVER place your face or body in line with the cutting tool. Avoid awkward operations and hand positions where sudden slip could cause fingers or hand to move into a sawblade or other cutting tool.

DO NOT use the rip fence as a length stop. However, since these are usually quite hard and slippery, the anti-kickback pawls may not stop a kickback. Therefore, be especially attentive to following proper set-up and cutting procedures for ripping. Do not stand, or permit anyone else to stand, in line with a potential kickback.

If ripping at the time, check to see if rip fence is parallel with the sawblade. Readjust as indicated. NEVER gang crosscut — lining up more than one workpiece in front of the blade stacked vertically, or horizontally. The blade could pick up one or more pieces and cause a binding or loss of control and possible injury. DO NOT remove small pieces of cut-off material that may become trapped inside the blade guard while the saw is running.

This could endanger your hands or cause a kickback. Dull, gummy or improperly sharpened or set cutting tools can cause material to stick, jam, stall the saw, or kickback at the operator. Minimize potential injury by proper cutting tool and machine maintenance. NEVER use grinding wheels, abrasive cut-off wheels, friction wheels metal slitting blades wire wheels or buffing wheels. Crosscutting operations are more conveniently worked and with greater safety if an auxiliary wood facing is attached to the miter gauge.

See Page Make sure the top of the cutting tool rotates toward you when standing in normal operating position. Also make sure the cutting tool, arbor collars and arbor nut are installed pro p- erly.

Keep the cutting tool as low as possible for the operation being performed. Keep all guards in place whenever possible. Never use a cutting tool larger in diameter than the diameter for which the saw was designed.

For greatest safety and efficiency when ripping, use the maximum diameter blade for which the saw is designed, since under these conditions the spreader is nearest the blade. Make sure the table insert is flush or slightly below the table surface on all sides except for rear side. NEVER operate the saw unless the proper insert is installed. Do not allow familiarity gained from fre-! Always remember that a careless fraction of a second is sufficient to inflict severe injury.

The operation of any power tool can result in foreign objects being thrown into the eyes, which. Some dust created by power sanding,! Some examples of these chemicals are:.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. If your tool is equipped with a po arl zedi plug one blade is wider than the other , this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.

If it still does not fit, contact a qualified electrician to install the proper outlet. To reduce the risk of electric shock, do not change the plug in any way. Always use proper extension cord. If an extension cord is necessary, a cord with adequate size con ductors should be used to prevent.

The table shows the correct size to use, de pending on cord length and nameplate amperage rating of tool. If in doubt, use the next heavier gauge. Always use U. NOTE: The smaller the gauge number, the heavier the cord. The item on which the cutting operation is being performed. The surfaces of a workpiece are commonly referred to as faces, ends and edges. Device which, when properly maintained, is designed to stop the workpiece from being kicked back at the operator during operation.

A cutting or shaping operation made across the width of the workpiece cutting the workpiece to length. A non-through cut which produces a square sided notch or trough in the workpiece. A device which can help guide workpieces during rip type operation by keeping workpiece in contact with the rip fence. It also helps prevent kickback.

Performing a cut without a fence, miter gauge, fixture, hold down or other proper device to keep the workpiece from twisting during the cut. You may be dragged into the blade during a kickback. Always set and maintain the rip fence parallel to the saw blade. A misaligned fence could cause the workpiece to become like a wedge and bind the spinning saw blade.

Set blade height for through cutting to just above the workpiece thickness. Minimizing exposure of blade body will reduce the tendency of blade binding on body of saw blade. Keep hood guard assembly, spreader and anti-kickback pawls in place and operating properly. Replace or sharpen anti-kickback pawls when points become dull.

Check their action before ripping. The spreader aligned with the saw blade and the pawls are intended to stop a kickback once it has started. Feed force must be applied only between fence and blade.

Never apply pressure to the side of the blade. Pressure applied to the side of the blade will cause the blade to stall or kickback the workpiece. When performing a bevel rip cut, always place the fence to the right of the blade. On this particular table saw the blade tilts to the left. Bevel ripping with the fence on the left side may not allow the use of the push stick and will wedge the workpiece between the blade and the fence.

Be aware of increased blade exposure on the right side of the guard, when setting the blade for bevel angle. Never cut freehand! Use the fence to support the length of the workpiece in ripping cuts and the miter gauge for cross cut operations. Unsupported or improperly supported workpieces may bind and kickback. Never attempt to pull the workpiece through the spinning saw blade. You may experience a kickback and be dragged into spinning saw blade. Do not release work until you have pushed it all the way past the saw blade.

Keep your hands away from side and to the rear of a spinning saw blade. A kickback can drag your hand into the blade if it is positioned on the workpiece, to the side or behind the blade.

Use a Push Stick for ripping widths of 2" to 6" and an auxiliary fence and Push Block for ripping widths narrower than 2". When ripping, apply the feed force to the section of the workpiece between the saw blade and the rip fence. If your hand or fingers are within 6 inches of the spinning blade you are too close to be able to react in case of a kickback event and you may be injured.

The blade guard system is not effective for narrow rip cuts and will not prevent kickback if blade becomes bound.

Do not rip workpiece that is twisted or warped or does not have a straight edge to guide along the rip fence. Workpieces without a straight edge will tend to wedge themselves between blade and fence possibly causing a kickback. Whether performing straight cross cutting or miter angle cross cutting operations, always follow these warnings:. When cross cutting, never use the rip fence and the miter gauge together. They will act against each other and bind the work on the blade leading to kickback.

Use the guard system for the cross cuts. The guard is not just for rip cutting. If the workpiece is too small, affix a jig or other means to fix workpiece to miter gauge during a cross cut operation. This lets you properly hold the miter gauge and workpiece while keeping your fingers away from blade. Never attempt to plunge cut into a workpiece by placing it on top of the spinning blade.

The workpiece will kickback. Lower the blade below table surface, remove the guard system, clamp feather boards or other fixture to hold workpiece down, and against the fence.

Place the workpiece on the tabletop at the desired location. Start the saw and let it come to full operating speed then slowly raise the blade until it pierces the workpiece and then push the workpiece through the desired length. To stop the cut, shut off the saw, lower the blade and remove workpiece.

Repeat as necessary to complete all sides of the pocket cut. Pay attention to the proximity of your fingers to blade. Remember that removing the hood guard assembly also removes the anti-kickback devices, the spreader and anti-kickback pawls!

Immediately replace guard assembly guard, splitter and anti-kickback pawls after special applications that cannot use the guard assembly such as resawing, dadoing, rabbeting or molding. For all non-through cutting, the operator must use feather boards to reduce the hazard from a kick back! Use feather boards to help guide and stabilize cutting so you can concentrate on the cutting action. Feather boards are not replacement for a guard and they cannot keep your fingers from accidentally contacting the blade.

Use the fence to guide and support the work past the saw blade. Unsupported cuts will shift and may cause the work to be thrown backward. Use the proper table insert for the width and diameter of the dado blade or molding head. Dado blade stack or molding head is wider than the slot of the standard table insert. These blades will strike and damage the standard insert and cause severe injury by throwing the insert against the operator.

Do not bevel with dado blades or molding heads. These accessories are designed for perpendicular non-through cutting.

Do not elevate the dado blade so that the hub protrudes above slot of the table insert. Contact with hub will cause the workpiece to be unstable as it passes through the cut and possibly kickback. Dado blades create wide non-through cuts that require the operator to feed the work slowly and use of feather boards and positive downward pressure on the workpiece to avoid loss of control.

Do not back up or pull the workpiece back reverse feed when resawing. Pulling the workpiece backward could cause kickback.

Table saws are highly versatile products capable of performing variety of operations. There are too many applications to be fully addressed in this manual. Some dust created by power sanding,!

Some examples of these chemicals are:. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. NOTE: The smaller the gauge number, the heavier the cord. Unpacking and Checking Contents. Bevel Crosscutting.

The item on which the cutting operation is being performed. The surfaces of a workpiece are commonly referred to as faces, ends and edges. Device which, when properly maintained, is designed to stop the workpiece from being kicked back at the operator during operation. A cutting or shaping operation made across the width of the workpiece cutting the workpiece to length.

A non-through cut which produces a square sided notch or trough in the workpiece. A device which can help guide workpieces during rip type operation by keeping workpiece in contact with the rip fence.

It also helps prevent kickback. Performing a cut without a fence, miter gauge, fixture, hold down or other proper device to keep the workpiece from twisting during the cut. A sticky, sap-based residue from wood products.

Misalignment of the blade which causes the trailing or outfeed side of the blade to contact the cut surface of the workpiece. Heel can cause kickback, binding, excessive. In general, heel creates a poor quality cut and can be a safety hazard. The amount of material removed by the blade in a through cut or slot produced by the blade in a non-through or partial cut. An uncontrolled grabbing and throwing of the workpiece back toward the front of the saw during a rip type operation.

The end of the workpiece which, during a rip type operation, is pushed into the cutting tool first. Use the Push Stick for rip widths less than 6 inches and more than 2 inches.

A device used for ripping-type operations too narrow to allow use of a Push Stick. Use a Push Block for rip widths less than 2 inches. A cutting operation along the length of the workpiece cutting the workpiece to width. Gardez toujours les yeux sur votre travail. Faites preuve de bon sens. Portez une coiffure de protection si vous avez les cheveux longs. Attachez les cheveux longs et retroussez vos manches au-dessus des coudes. Il y a risque de contact accidentel avec la lame en rotation.

Servez-vous de votre bon sens. Les rebonds peuvent causer des blessures graves. Les lames. Ne coincez pas la chute ou ne restreignez pas son mouvement lorsque vous refendez ou lorsque vous sciez en travers. Coincer la chute entre le guide et la lame cause un rebond.

Ne placez pas vos mains ou vos doigts sur la trajectoire de la lame. Ces produits chimiques sont, par exemple :. Lea y entienda el manual del usuario y las etiquetas puestas en la herramienta. No la use cuando se encuentre bajo la influencia de medicamentos o al tomar alcohol u otras drogas.

No se ponga ropa holgada ni joyas. Se recomiendan guantes de caucho y calzado antideslizante cuando se trabaja a la intemperie. Use cubiertas protectoras para el pelo a fin de sujetar el pelo largo. Evite el contacto del cuerpo con las superficies conectadas a tierra. No guarde mate-. Apague la herramienta. Siga las instrucciones para lubricar y cambiar los accesorios.

No corte metal con sierras de mesa. Sin embargo, como estos materiales son generalmente bastante duros y resbaladizos, es posible que los trinquetes antirretroceso no detengan un retroceso. Desenchufe la sierra antes de hacer ajustes, reparaciones o almacenamiento. Los arranques accidentales pueden causar lesiones personales graves.

Use calzado antideslizante. Si no puede controlar su movimiento, no puede controlar el trabajo. Nunca encienda la sierra antes de retirar de la mesa de todas las herramientas, residuos de madera, etc.

Las piezas de trabajo largas necesitan soporte adicional en el lado de avance de salida, como por ejemplo un soporte auxiliar o una base de soporte rodante. Si no puede ver el tablero de la mesa bajo la pieza de trabajo, la pieza es demasiado grande para cortarla de manera segura con la sierra de mesa.

Los retrocesos pueden causar lesiones graves. And heavy leaves and debris are cleared with the Power boost feature. This cordless blower kit includes a 2. Add more power and durability to your tool shed with a hedge trimmer powered by a digital brushless motor. With dual-action blades for clean and efficient cuts, hardened steel blades for longevity, and a digital brushless motor to keep it running longer without the hassle of gas.

This Hedge Trimmer kit includes a 2. This battery Hedge Trimmer includes a 2. Power through tasks faster with tool-less chain tensioning and auto-lubrication and have peace of mind with the anti-kickback brake. This battery chainsaw Kit includes a 2.

Industry-leading innovation from SKIL charges faster and more efficiently than ever. The charger manages each cell in the battery to control temperature and maximize battery life. Each cell is surrounded by temperature management material to keep the battery cool and powering on. Level up your lawn care game—without the hassle of gas— with a cordless string trimmer built for power and performance. And, when the task is complete, the telescoping handle folds down completely allowing for vertical storage.

This cordless lawn mower kit includes a 5. This electric lawn mower kit includes a 5. Its ultra-thin panel head provides up to lumens for greater visibility while you work. Use the rotating handle for a variety of positions to hang or stand, or use the keyhole hanger for a wall mount. This light brings powerful brightness to a variety of tasks, like painting the dining room or working in tight spaces.

With two ultra-bright LED panels to illuminate large work areas with ease. Choose from three settings—high lumens , low lumens , or single panel lumens —and easily rotate either panel to direct light. The Solution for Precision Cutting From cutting to sanding, scraping to chipping, this oscillating tool can do it all. This oscillating tool features the innovative Vibration Reduction System VRS which isolates the motor from the body of the tool to reduce vibration transfer and increase comfort, so you can power through hard cuts with ease.

Convenient Measuring with the Tap of a Button This compact laser measurement tool can record distances up to 65 feet. Use the intuitive controls to access distance and continuous measuring modes, or to calculate area. Need to measure a curved or uneven surface? Use the wheel measuring mode instead like a laser tape measure.

Plus, you can easily toggle between imperial and metric with the press of a button. Now you can measure with ease and convenience with a laser distance measure from SKIL. Easily switch between linear and orbital mode, or adjust depth of cut with the pivoting shoe. Counterweights transfer less vibration, helping you work more comfortably. Includes the power and performance of the SKIL 4.

A Powerful Router for Any Project. Speed control dial provides the right speed for the material, and LED lights on the motor base illuminates the work area. The pistol grip handle delivers versatility with a simple twist to fit into tight spaces, while the LED light offers precision in dimly lit areas and the cam screw sleeve provides quick and easy support for furniture assembly. Every home needs a go-to rechargeable screwdriver, and this one checks all the boxes.

This laser automatically levels and features intuitive indicators so you know when your lines aren't level. And, for projects where you might not want your lines to be level or plumb, like specialty paint treatments or diagonal tile work, the SKIL Self-Leveling Laser Level locking feature allows you to position the projected lines at any angle you choose.

The 4-Stage Orbital Selection provides high cutting efficiency for different materials, producing up to 3, strokes per minute, while the built-in dust blower and Halo LED light provides clear lines for precise cutting. The 4-Stage Orbital Section provides high cutting efficiency for different materials, producing up to 3, strokes per minute, while the built-in dust blower and Halo LED light provides clear lines for precise cutting. The Brushless motor provides efficiency, performance, and extends the lifespan of the tool.

The 3-speed design provides versatility while clearing debris from ground or overhead, while the variable speed trigger and speed lock provides maximum control while delivering performance up to CFM and mph of air speed. These versatile power tools can help with a variety of tasks around the house, like installing shelves, loosening tough bolts, assembling new furniture, illuminating dark workspaces, cutting through tough materials during a teardown and more.

The tool automatically levels, and it features intuitive indicators that let you know when you're not level. Its bright green lines offer superior visibility, and the horizontal and vertical lines can project to a distance of 65 ft. The integrated, rechargeable Lithium-Ion battery has a micro-USB port for charge-and-go convenience, plus green, yellow, and red LED indicators to let you know the current charge status.

Get the everyday essentials you need to own your home or car, all in one convenient kit to cover your to-do list. With a High Pressure Mode and Auto Shutoff for hands-free inflating, the compact and lightweight design makes it perfect for use in the car.

This hammer drill gives you three tools in one with easy transitions between the hammer drill, drill, and screwdriver modes, as well as quick bit changes to save you time and keep your job going. Get the everyday essentials you need to OWN your project, all in one convenient tool kit.

Choose from 17 torque settings to take control with the IN. The cordless circular saw is equipped with an tooth, thin kerf carbide-tipped blade and durable steel shoe, delivering quick clean cuts, while the integrated dust blower keeps cut lines clean and visible for ultimate precisions. From tackling repairs to major remodeling and demolition projects, the brushless SKIL cordless reciprocating saw makes quick cuts a breeze with its lightweight design, providing compact power and easy overhead use.

The high-performance brushless motor makes this electric hand saw strong enough to cut through lumber, PVC piping, tree branches, and metal. This brushless combo kit has you covered for any job, big or small.

Utilize the ft. Its compact design makes it easy to use, while its 22oz dust container and high-suction capability make it a must-have. This 20V tire inflator can take on everything from bicycle and car tires to sports balls. This versatile cordless electric sander vibrates and spins simultaneously for a smooth finish.

The powerful motor is equipped with Variable Speed Control to maximize efficiency at 7,, OPM, while the hook-and-loop pad provides quick and easy change of sandpaper grits. Level up your lawn care game — without the hassle of gas — with this 14 IN. The patented Twist Load Head on the string trimmer makes it easy to load. Simply insert the line and twist to get started. With the Dual-Line Bump Feed you can load more line hassle-free so you can cut through thick grasses and weeds with ease.

The battery has an integrated USB port to allow for on-the-go charging of your devices, while the lightweight and ergonomic handle reduces user fatigue. The integrated foldable legs seamlessly form into a folding stand to provide portability and convenience, while the dust port elbow systematically redirects dust to a container for easy cleanup. The parallel blade alignment allows for ease of blade adjustment along the rip fence and miter slot, for precise accurate cuts.

This table saw features a safety anti-restart switch in case of power outages. When using a dado insert, this table saw requires an 8 in. A tough job is no match for this powerful 7. The 2-finger, variable-speed trigger , RPM has a convenient lock-on feature for increased control during driving and drilling. And the 48,BPM provides the power needed for tough applications. This kit also includes a Piece bit set for drilling into surfaces like wood, metal, plastic, and masonry. The tool features a brushless motor that delivers uncompromised performance while allowing for a compact, lightweight design.

It has a variable speed trigger and a 1 IN. The counterbalance gearbox provides vibration dampening to allow for greater precision and control, while the tool free blade change capability provides swift changes on the go.

This miter saw features a horizontal grip handle with a center located safety trigger for left- or right-handed use. The 9 detents on the stainless-steel miter plate and 11 miter locations allows for degree cuts left or right, with 11 positive stop positions at commonly used angles. The LED Shadow Line provides high precision cuts with greater accuracy than traditional lasers, while the lightweight design and built-in carrying handle provide convenience and portability.

The quick work clamp quickly secures materials for safer cutting. Circular Saw Kit. Shine light where you need it most. Depending on your need, choose between high, low, or strobe from the illumination settings while utilizing the built-in metal hook, rafter hook, and magnets to attach to the hood of a car.

The LED lights strobe feature is a handy way of alerting oncoming drivers if you are on the side of the road during an emergency. Powerful and task efficient. This tool offers a host of user-friendly features, such as a paddle switch and onboard wrench storage. The ergonomic design, soft rubber grip, and 3-position side handle provide more comfort and control, so you can work longer.

The full-frame, linear counterbalance stops vibration at the source, instead of moving it around and shifting it to the user, as other saws do. Set-up for the job is quick and easy with tool-less latches to secure the miter saw.

Designed for portability, it only weighs Extendable material supports that can extend up to 8 ft. A worm drive table saw needs a stand that can stand up to any job. Portable Worm Drive Table Saw, set-up for the job is quick and easy.

Tool-less latches quickly secure the table saw and an adjustable leg makes leveling simple. Designed for portability, it only weighs 14 lbs. And folds flat for easy transportation. Make impossible cuts, possible. Backed by legendary Worm Drive gearing, the 16 IN. Carpentry Chainsaw combines power and durability for extraordinary productivity. The full house chain provides precision, giving you cleaner, accurate cuts in a fraction of the time.

Featuring magnesium built construction, this chainsaw delivers a lightweight design — allowing for maximum control and efficient handling.

The impossible is possible with SKIL. Nobody has to tell you or your tools to go above and beyond every day. Dry Cut Saw to cut like a 14 IN. The powerful amp motor and no load 1, RPM cuts faster and cleaner than a chop saw—no deburring needed. Nobody has to tell you to go above and beyond every day. The powerful 15 Amp motor and no load 1, RPM cuts faster and cleaner than a chop saw- no deburring needed. With the legendary strength and grit of a SKIL, this lean, mean chop saw for metal is a powerful ally to have in your corner.

Our 14 IN. Abrasive Chop Saw weighs in at From the name generations of pros already know, the 14 IN. Now you can power through stacks of fiber cement while the silica dust is funneled away from the tool motor for longer life.

The unique included no-mar cord sleeve keeps the vacuum hose and power cord from getting in your way. Cut siding and trim straight and clean all day with less fatigue, thanks to the lightweight yet rugged magnesium components. Rugged all-magnesium construction reduces weight and goes even further to dissipate motor heat.

See it all: with your blade located on the left, you have improved blade and cut-line visibility for improved accuracy. Count on legendary SKIL durability and performance to get the job done. The rugged magnesium housing stays strong and keeps the motor cooler, giving you powerful performance for a lifetime.

Did we say a Diablo blade is included? Top it off with a brake and the degree precision beveling capacity and you will be unstoppable. Worm Drive Skilsaw is the new boss. The biggest worm drive saw on Earth tears through whatever you throw at it. The magnesium, die-cast foot plate guarantees true, square cuts every time.

SKIL blade makes perfect cuts right out of the box. No matter what the material, this worm drive Skilsaw is built to be relentless with its 15 Amp dual field motor designed specifically for saws. It keeps the motor cooler, providing increased power and durability for the life of the saw. Only SKIL has it. Increase your productivity on the jobsite by making one clean cut the first time, every time.

True to the trade since SKIL worm drive Skilsaw. No matter what the material, this worm drive saw is built to be relentless with its 15 Amp dual field motor designed specifically for saws. With the power and torque to tackle difficult cuts, bogging down is a thing of the past. Without sacrificing legendary SKIL durability, you get a compact and portable saw that will be the talk of the jobsite. Welcome to the next chapter in the Worm Drive legacy.

The original Worm Drive Skilsaw, often called the saw that built America, just got better. At 1 lb. This model even comes with a Diablo blade, just to make sure your Skilsaw is tough as nails right out of the box. The original Worm Drive, lighter and better than ever. At 3 lbs. Unstoppable durability meets lightweight ease for long days and a motor that stays cooler for years of heavy use. The latest and lightest Worm Drive continues the long tradition of SKIL quality, rugged durability and consistently exceptional cutting performance.

Weighing in at just The rugged magnesium housing stays strong but keeps the motor cooler, giving you powerful performance job after job. This model comes with a SKIL blade.

You get a Diablo blade, too, to round things out. After all, the best saw should get the best blade. This model has a Twist Lock plug.

The 8 IN. This Worm Drive Skilsaw changes the game because it has the strength and guts to tackle whatever is thrown its way with its Worm Drive gearing customized for metal.

Others settle, but this Worm Drive has the edge to see things others never will. The blade window gives you the visibility to make true cuts. This saw also comes with the largest available chip tray, so you can stay productive. And each pass of the saw with the SKIL carbide-tipped blade cuts quickly and virtually spark-free, with minimal burrs- showing metal no mercy. It's the saw made for those who rewrite the rules. Others settle, but this Worm Drive Skilsaw has the edge to see things others never will.

This Skilsaw also comes with the largest available chip tray, so you can stay productive. And each pass of this saw with the Diablo Cermet blade cuts quickly and virtually spark-free, with minimal burrs- showing metal no mercy. Exclusive degree bevel.

Legendary SKIL durability. And a Diablo blade is included in the box. What more could you ask for? Forget modifying an old saw. Used wet or dry, the dual integrated dust management system takes dust out of your way. And rust resistant brackets and fasteners resist corrosion for long life.

Stand up to big jobs with the only worm drive walk behind concrete saw. Cutting long control joints is simple with the new integrated handle that adjusts to your height and folds easily for transport and storage. Our legendary SKIL worm drive power and a pivoting pointer deliver unmatched precision and convenience.

Used wet or dry, the integrated dust management system controls dust for cleaner cuts. A two-finger trigger reduces user fatigue and improves control. The all metal components featuring rust-resistant brackets and fasteners protect from corrosion for longer life. You can always count on SKIL. With the legendary strength and grit of a SKIL , this lean, mean chop saw for metal is a powerful ally to have in your corner.

But being light doesn't mean it's any less tough. The versatile "D" handle gives you comfort and control cut after cut. A mightier miter saw. Backed by legendary Worm Drive gearing, the 12 IN. Dual Bevel Sliding Miter Saw combines dependable quality and lightweight portability into one powerful tool.