Att e5640 manual

What does this limited warranty cover? Page 33 Limited warranty 3. How long is the limited warranty period? If AAT repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to repaired or replacement Products for a period of either a 90 days from the date the repaired or replacement Product is shipped to you or b the time remaining on the Page 35 Limited warranty 6.

What must you return with the Product to get warranty service? Page 36 Limited warranty Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall AAT be liable for any indirect, special, inci- dental, consequential, or similar damages including, but not limited to lost profits or revenue, inability to use the product, or other associated equipment, the cost of substitute equip- ment, and claims by third parties resulting from the use of this Page 37 www.

All rights reserved. Printed in China. Print page 1 Print document 37 pages. Rename the bookmark. Delete bookmark? Cancel Delete. The EB has 3 handsets automatically registered as handset 1, 2 and 3. You can register one additional handset, which will be called Handset 4. During registration, you must enter the digit ID number of the telephone base.

For the E, you can find the base ID code in the E base menu. NOTE: A maximum of two handsets or one handset and the speakerphone on the telephone base can be connected to an external line anytime.

If this happens, return the handset to the handset charger until the screen shows. The number is located on the bottom of the E and EB telephone base. Treat that as part of the base ID and enter it into the handset for registration purpose.

When a valid base ID has been entered and recognized by the telephone base, the screen will be blank for a few seconds and will show:. The new handset will be assigned the next available handset number Handset 2, Handset 3, or Handset 4. A maximum of four handsets can be registered to each telephone base. If you are replacing a handset on a system which already has the maximum number of handsets registered 4 , or wish to change the assigned handset number of your registered handsets, you must first de-register all handsets, then re-register them again.

This should take about 10 seconds. Once the base indicators turn off may take up to 30 seconds , the handsets are de-registered from the telephone base, and can now be re-registered see page 9. All handsets will be de-registered from the telephone base and the handsets will display may take up to 30 seconds :. The handsets are now de-registered from the telephone base, and can now be re-registered see page 9. Welcome to ManualMachine. We have sent a verification link to to complete your registration.

Log In Sign Up. Forgot password? Enter your email address and check your inbox. While pre-dialing, press to delete digits from a string see page Speaker Press to activate handset speakerphone. V DIR Press to scroll down in menus. Intercom Press to initiate an intercom conversation or transfer a call see pages See page 18 Call Log See page 22 Ringer Volume See page 16 Ringer Tone See page 16 Key Tone See page 16 Language See page 17 Dial Type See page 17 Menu.

Getting Started Quick reference guide Telephone Base. Handset Locator Press to make handset s beep see page Volume Press to adjust message playback volume. Charging In Use. On when handset is positioned so its battery can charge. Answering System Controls see pages Press to play or stop playing messages.

Press to delete a message during play back. Press to review or set the answering system clock. Press to review or change answering system options.

Press to change a menu option. Press to record a memo or, after pressing MENU, to record an outgoing announcement. Getting Started Parts checklist for E Remember to save your sales receipt and original packaging in case you ever need to ship your telephone for warranty service. Check to make sure the telephone package includes the following: Telephone base Telephone handset Power adapter Belt clip Battery Telephone line cord Wall mount bracket.

Getting Started Parts checklist for EB Remember to save your sales receipt and original packaging in case you ever need to ship your telephone for warranty service. Check to make sure the telephone package includes the following: Telephone base Telephone handsets Handset chargers Power adapters Batteries Wall mount bracket Belt clips Telephone line cord. Getting Started Before you begin. Telephone operating range This cordless telephone operates with the maximum power allowed by the Federal Communications Commission FCC.

Getting Started Telephone base installation Install the telephone base as shown below. Press tab to open battery compartment. Volume Press to adjust message playback volume. Charging In Use. On when handset is positioned so its battery can charge. Press to play or stop playing messages. Press to delete a message during play back. Press to review or set the answering system clock. Press to review or change answering system options. Press to change a menu option. Press to record a memo or, after pressing MENU, to record an outgoing announcement.

Getting Started Parts checklist for E Remember to save your sales receipt and original packaging in case you ever need to ship your telephone for warranty service. Check to make sure the telephone package includes the following: Telephone base Telephone handset Power adapter Belt clip Battery Telephone line cord Wall mount bracket. Getting Started Parts checklist for EB Remember to save your sales receipt and original packaging in case you ever need to ship your telephone for warranty service.

Check to make sure the telephone package includes the following: Telephone base Telephone handsets Handset chargers Power adapters Batteries Wall mount bracket Belt clips Telephone line cord. Telephone operating range This cordless telephone operates with the maximum power allowed by the Federal Communications Commission FCC.

Getting Started Telephone base installation Install the telephone base as shown below. Press tab to open battery compartment. Plug power adapter into an electrical outlet not controlled by a wall switch. Replace compartment cover. Place handset in base or charger to charge for 16 hours before first use. Getting Started Wall mounting The base can be installed on any standard wall-phone outlet as shown below.

Install the line cord as shown in the diagram. Plug telephone line cord into telephone jack. Clip wall-mount bracket securely into notches on underside of base.

Snap belt clip into notches on side of handset. Rotate and pull to remove. Plug 2. Telephone Operation Elapsed time Basic operation. You can only view or download manuals with. Sign Up and get 5 for free.

Upload your files to the site. You get 1 for each file you add.